Thanks.  Its been added (you can do that yourself btw)

Regards

TK

 

Tom, this should be added to your wiki.

All, the solution was to follow the exact steps for Windows 10 prep.  The signed drivers install with no error message, but do not work for Windows 8.1 Industry Embedded Enterprise.  I skipped to the following steps:

Click the “Start” button Type “cmd” Right-click the “Command Prompt” listed in the “Start Menu” and choose “Run as Administrator” Click the “Yes” button Type “bcdedit.exe –set loadoptions DDISABLE_INTEGRITY_CHECKS” without quotes (note: there are two ‘D’s in ‘DDISABLE’ Press the “Enter” key – you should see “The operation completed successfully.” Type “bcdedit.exe –set TESTSIGNING ON” without the quotes Press the “Enter” key – you should see “The operation completed successfully.” Reboot the computer This has succeeded if the screen says “Test Mode” in the bottom right corner

Setup Driver for KFlop Board

Make sure that the controller is powered on and that the USB cable is connected between the computer and the controller.

• Click the “Start” button and type “Device Manager”
• Press the “Enter” key
• Under “Other Devices”, right-click “KFLOP – Motion Controller” and choose “Update Driver Software…”
• Click the “Browse my computer for driver software” button
• Use the “Browse…” button to select the folder that KMotion was installed in (i.e. “C:\KMotion433q”)
• Click the “Next” button
• On the “Windows Security” screen, click the “Install this driver software anyway” button
• The screen should end with “Windows has successfully updated your driver software”
  

 

On 2016-11-18 14:26, kn6za@... [DynoMotion] wrote:
> Anyone know what the minimum system req. are for 4.34e? My xp system
> ran 4.33 fin but is a no go now.
>

 

Tom,

   After update the problem remains. Looks like the .net framework 4.6.2 has win 7 as minimum req.

  xp is capable of .net framework 4. only

   When I install 4.34e it does prompt for vs2015 but gives me a blocking message about the .net framework system requirement not being met.

  Andrew

Hi Andrew,

Please try unzipping and copying these Microsoft Universal c Run Time Libraries to the C:\KMotion434\KMotion\Release folder to see if it solves the problem.

http://dynomotion.com/Software/UCRTx86.zip

Regards

TK

 

Oh thanks Tom! 

I will look into the update status. I am confident that is probably the issue as that system is not connected to the net.

  Good to know xp should still viable as all my machine systems are still running essentially discarded computers.

   Andrew

Hi Andrew,

Please download this, unzip it, copy the 4 files to C:\KMotion434e\KMotion\Release and see if KMotionCNC.exe runs.

http://dynomotion.com/Software/Patch/KMotionCNC_Compiled_for%20PlatformXP_V434e/KMotionCNCFilesXPv434e.zip

Regards

TK

 

Hi Tom,

   Thanks!

   That fixed a vista computer that popped up an error about api files missing after installing. 434e now runs on a vista system that was choking.

  The xp system still pops the same not a valid win32 application error.

   Andrew

Hi Andrew,

Do you have XP Service Pack 3?

Have you ran Windows Update?

Regards

TK

 

Hi Tom,

   Same problem.

   If i attempt to run the application in the temporary zip extract folder or in the proper release folder i get the same error message.

 Andrew

Hi Andrew,

I see from timestamps I included the old KMotionCNC.exe by mistake and also forgot KMotionServer.exe

Please download, unzip, and copy the files from here again:

http://dynomotion.com/Software/Patch/KMotionCNC_Compiled_for%20PlatformXP_V434e/KMotionCNCFilesXPv434e.zip

I'm not sure how to check Windows Updates other than Update History.

Regards

TK

 

 Hi Tom,

Just checked a fresh 434e install on a different xp system, and added the files from our last few rounds to the release folder and get the same result on all three.

not a valid win32 application 

vs2015 is being automatically installed without a problem, so I did not go to the windows site to download it this time. The .net framework gave the same minimum system error.

All three are service pack 3 in the control panel system tab.

Is there a way to check that the windows updates have executed properly?

  Andrew

Hi Andrew,

ok great.  Thanks for your patience. I was trying to go one step at a time.

Please download the zip again and it should include 6 files including KMotion.exe

Regards

TK

 

Hi Tom,

   kmotioncnc is working now, but Kmotion needs the fix as well.

  Andrew

Tom its a pleasure using your product, and service like this on a Saturday is AMAZING!

I will grab the .zip

Thanks again!

Andrew

On Nov 19, 2016, at 6:23 PM, "Tom Kerekes tk@... [DynoMotion]" <DynoMotion@yahoogroups.com> wrote:

 

Hi Andrew,

ok great.  Thanks for your patience. I was trying to go one step at a time.

Please download the zip again and it should include 6 files including KMotion.exe

Regards

TK

On 11/19/2016 2:35 PM, kn6za@... [DynoMotion] wrote:

 

Hi Tom,

   kmotioncnc is working now, but Kmotion needs the fix as well.

  Andrew

Hi Vetsen,

The Slit Screen should work under XP you should just need to select it.

You only need a more up to date computer OS to run the KMotionCNC Screen Editor to make changes.  Don't you have temporary access to a newer computer?

Regards

TK

 

Hi Tom,

I'm trying out the 4.34E test version too.

I was having the same problems on XP, not being able to launch kmotionCNC.exe..   I have applied all your patches that you posted to this thread.  I can launch the kmotion CNC.EXE  now, but when I try to launch the kmotion cnc screen editor I get  "KMotionCNCscreenEditor.exe is not a valid win32 application." 

Could this also need to be patched?

I'm excited to try the split gcode/gviewer screen

thanks,

Vetsen

BTW, I used .NET V4.0 installer on XP and it seemed to work so far, apart from the screeneditor not loading.